Тел.: 8(495)724-94-22

 8-903-724-94-22

Факс: 8(499)978-97-26

E-mail: Этот адрес электронной почты защищен от спам-ботов. У вас должен быть включен JavaScript для просмотра.

KSHP. OMD №11-2014

Category: Content
Published on 05 December 2014
Written by kshp. omd Hits: 918

CONTENTS № 11–2014

75th ANNIVERSARY OF THE DEPARTMENT «MECHANICS OF PLASTIC FORMING» OF THE TULA STATE UNIVERSITY
(selection of articles)

Yakovlev S.S., Larin S.N. The history of the Department "Mechanics of plastic forming" of the Tula state University, p. 3–9

Kukhar’ V.D., Kireeva A.E. Influence of pre-heating billets made of aluminum alloy D1M on magnetic-pulse stamping process, p. 10–13

Chudin V.N., Yakovlev S.S. Axisymmetric backward extrusion in terms of viscoplasticity, p. 14–17

Panfilov G.V., Nedoshivin S.V. Development of analytical method of slip bands in relation to the problems of flat plastic flow, p. 18–27

Yakovlev, S.S., Remnev K.S., Pilipenko O.V. Loss of stability of round billets from anisotropic materials during reduction, p. 27–31

Remnev, K.S., Yakovlev S.S., Kalashnikov A.E. About stability loss of thin anisotropic billets during axisymmetric parts drawing, p. 32–35

Gryazev M.V., Yakovlev S.S., Tregubov V.I. Rotary drawing of axisymmetric shells from anisotropic materials with separation of the deformation zone, p. 35–40

Evdokimov A.K., Nazarov K.A. Improvement of manufacturing annular gas cylinders, p. 40–45

Kukhar’ V.D., Pas’ko A.N., Begov P.Yu. Influence of tool geometry in production of waveguide tubes by cold stamping, p. 46–48

CONTENTS № 11–2014
 
75th ANNIVERSARY OF THE DEPARTMENT «MECHANICS OF PLASTIC FORMING» OF THE TULA STATE UNIVERSITY
 
(selection of articles)
 
Yakovlev S.S., Larin S.N. The history of the Department "Mechanics of plastic forming" of the Tula state University, p. 3–9
 
Kukhar’ V.D., Kireeva A.E. Influence of pre-heating billets made of aluminum alloy D1M on magnetic-pulse stamping process, p. 10–13
 
Chudin V.N., Yakovlev S.S. Axisymmetric backward extrusion in terms of viscoplasticity, p. 14–17
 
Panfilov G.V., Nedoshivin S.V. Development of analytical method of slip bands in relation to the problems of flat plastic flow, p. 18–27
 
Yakovlev, S.S., Remnev K.S., Pilipenko O.V. Loss of stability of round billets from anisotropic materials during reduction, p. 27–31
 
Remnev, K.S., Yakovlev S.S., Kalashnikov A.E. About stability loss of thin anisotropic billets during axisymmetric parts drawing, p. 32–35
 
Gryazev M.V., Yakovlev S.S., Tregubov V.I. Rotary drawing of axisymmetric shells from anisotropic materials with separation of the deformation zone, p. 35–40
 
Evdokimov A.K., Nazarov K.A. Improvement of manufacturing annular gas cylinders, p. 40–45
 
Kukhar’ V.D., Pas’ko A.N., Begov P.Yu. Influence of tool geometry in production of waveguide tubes by cold stamping, p. 46–48