Тел.: 8(495)724-94-22

 8-903-724-94-22

Факс: 8(499)978-97-26

E-mail: Этот адрес электронной почты защищен от спам-ботов. У вас должен быть включен JavaScript для просмотра.

KSHP. OMD №10-2014

Published on 05 December 2014
Written by kshp. omd Hits: 977

A.L. Vorontsov

The consideration of the elastic deformation of the tool to increase the accuracy of the theory of processing by pressure

Part 2 The main stage of reverse extrusion of glasses

The necessity of consideration of the elastic tool deformation to characterize some forming processes is shown оn the examples of reverse extrusion of glasses and closed die forging.

Keywords: elastic tool deformation; extrusion of glasses; closed die forging.

 

R.E. Gliner, T.V. Nuzhdina, C.V. Yatunin, E.B. Katuhin

The symptom of hardening of copper during rotary extractor in the production of cumulative facings

Particular qualities of hardening of copper during rotary extractor are examined. The analysis conducted in relation to technology of the production of cumulative facings with technically pure copper. The using of cold-rolled strip in this technology is recommended.

Keywords: copper; rotary extractor; hardening; hardness; residual stress; annealing

 

M.I. Poksevatkin, K.Yu. Dunaev, A.S. Lavrinenko, N.A. Belenko

Condition implementation of monotonicity of the process of formation of core products

The method of determination of process parameters stamping is developed with implementing conditions for the monotonicity conditions shaping process products.

Keywords: blank; core products; longitudinal stability; billet; landing; monotony of the process.

 

A.N. Levanov

Features of contact friction in the processing of metals by pressure

Setup scheme is presented for the experimental study of contact friction in the processing of metals by pressure. Given experimental data of dependence of the friction stresses from normal pressure and contact slides with cold-formed aluminum, illustrating the possibility of improvement of technological processes.

Keywords: contact friction; die; preliminary displacement; the contact layer.

 

D.I. Braslavsky, I.A. Izakov, A.I. Kapitanenko

Research opportunities of isothermal forging blades of alloy ХН45МВТЮБР-ИД

It is determined thermomechanical deformation parameters of the alloy ХН45МВТЮБР-ИД (degree of deformation, high-speed parameters) necessary for the manufacture of an experimental batch of die blades with an allowance for machining up to 0.3 mm using the combined scheme of deformation: hot forging, isothermal forging in the air and cold stamping dies tense constructions.

Keywords: isothermal forging; stamped blades; recrystallization.

 

V.A. Kharitonov, I.V. Taranin

The study of the efficiency of manufacturing wire combined method «rolling-drawing in the monolithic portage with prop»

Combined method of manufacturing a wire «rolling-drawing in the monolithic portage with prop » is proposed. Shows the conditions for the implementation of the proposed method. Based on finite element modeling is found that the prop allows to reduce the magnitude of the tensile stresses in the deformation zone and tension lugs, thereby to increase the efficiency of the process compared with traditional drawing.

Keywords: wire; combined methods of material working by pressure; rolling-drawing in the monolithic portage with prop; stress state; the failure criterion.

 

A.K Belan, O.A. Belan

Technology features of producing wire and calibrated rolled steel for cold forming

The features of the technology of wire and calibrated rolled for subsequent cold forming of various types of fasteners are shown.

Keywords: wire; calibrated roll; drawing; fastener; cold forming; the degree of deformation; compression.

 

Yu.V. Kolotov

Device for hydrostatic molding of thin-walled products tubular billets with radial seal

In devices for hydrostatic molding of thin-walled products tubular billets used in the domestic and foreign industries, carry out the tightness of the butt-ends of the tube seal metal-to-metal produced by compressing the procurement of the axial force. This work describes a device for hydroforming with radial th seal inner cavity of the tube. It extends the technological capabilities of hydrostatic molding through the use of a tube with thinner walls and pain-necks in length.

Keywords: hydrostatic molding; thin-walled tubular billets; radial seal.

 

S.V. Filimonov, V.I. Lapshin, I.O. Lisin, V.I. Filimonov

Particularity of forming a closed H-beam using intensive deformation method with rolling

There are considered stages of forming a closed H-beam using intensive deformation method; pattern diagram and forming tool design are also given.

Keywords: roll-forming; forming tool; H-beam; split roll.

 

Yu.M. Antoshenkov, I.M. Tupac

Features modeling axisymmetric upsetting

The results of the simulation process axisymmetric upsetting of cylindrical samples with different ratio of height and diameter are shown. Analysis of stress-strain state of metal and energy-power parameters of the process are given.

Keywords: forging; sediment; modeling; finite element method.